FSP Hydro G Pro 1000W ATX v3.0 Power Supply Review

The FSP Hydro G Pro 1000W has top-notch build quality and it is ATX v3.0 and PCIe 5.0 ready.

The FSP Hydro G Pro 1000W has top build quality and compact dimensions. Its performance is decent, and the native 600W 12VHPWR connector will come in handy if you invest in a new NVIDIA GPU.

Pros

Full power at 47 degrees Celsius ATX v3.0 and PCIe 5.0 ready Good build quality Low ripple on all rails Efficient at normal loads Silent operating under normal temperatures High power factor readings Efficient 5VSB rail Long hold-up time Low leakage current Fully modular Loads of connectors, including a 600W 12VHPWR Compatible with the alternative sleep mode Compact dimensions Adequate distance between the peripheral connectors 10-year warranty

Cons

Overall performance needs boosting Mediocre transient response Not so tight load regulation at 12V and 3.3V Increased noise under high operating temperatures and loads High inrush currents Some EMI spurs went over the limits

The FSP Hydro G Pro 1000W is among the few Gold PSUs in this capacity category featuring ATX v3.0 and PCIe 5.0 compatibility. Its performance is decent, but it isn't high enough to allow it to earn a place in our best PSUs article. Competitors like the Corsair RM1000x and the EVGA 1000 G7 achieve notably higher overall performance scores.

The Hydro G Pro with 1000W max power belongs to the new generation of PSUs, featuring ATX v3.0 and PCIe 5.0 compatibility. There aren't many choices with native 12VHPWR connectors in the 1000W Gold category, and FSP was among the first to introduce a related product. Significant players, including Corsair, EVGA, and Seasonic, haven't released something on the market, yet. Thermaltake, with the Toughpower GF3 1000W, and Silverstone, with the DA1000R Gold, are two other choices in this category, meeting the ATX v3.0 spec for PSUs with 12VHPWR connectors.

With 150mm depth, the Hydro G Pro 1000 has compact dimensions. Nonetheless, FSP has the smallest, in dimensions, 1000W Gold platform, which is used in the EVGA 1000 G7, with only 130mm depth! Compact PSUs are easier to install, especially in smaller chassis, but the over-populated PCBs don't help airflow, hence noise output is usually increased. Moreover, it is not possible to install large enough cooling fans, with 135mm or 140mm diameter, in small PSUs, and smaller fans have to spin at higher speeds to offer the same airflow, producing more noise. The Hydro G Pro uses a 120mm, high-quality, fan, featuring a fluid dynamic bearing.

Specifications of FSP Hydro G Pro 1000W

Manufacturer (OEM)	FSP
Max. DC Output	1000W
Efficiency	80 PLUS Gold, Cybenetics Gold (87-89%)
Noise	Cybenetics A- (25-30 dB[A])
Modular	✓ (fully)
Intel C6/C7 Power State Support	✓
Operating Temperature (Continuous Full Load)	0 - 50°C
Over Voltage Protection	✓
Under Voltage Protection	✓
Over Power Protection	✓
Over Current (+12V) Protection	✓
Over Temperature Protection	✓
Short Circuit Protection	✓
Surge Protection	✓
Inrush Current Protection	✓
Fan Failure Protection	✗
No Load Operation	✓
Cooling	120mm Fluid Dynamic Bearing Fan (MGA12012XF-O25)
Semi-Passive Operation	✓ (selectable)
Dimensions (W x H x D)	150 x 85 x 150mm
Weight	1.72 kg (3.79 lb)
Form Factor	ATX12V v3.0, EPS 2.92
Alternative Low Power Mode (ALPM) compatible	✓
Warranty	10 Years

Power Specifications of FSP Hydro G Pro 1000W

Rail	Row 0 - Cell 1	3.3V	5V	12V	5VSB	-12V
Max. Power	Amps	20	20	83.33	2.5	0.3
Row 2 - Cell 0	Watts	Row 2 - Cell 2	120	1000	12.5	3.6
Total Max. Power (W)	Row 3 - Cell 1	Row 3 - Cell 2	1000

Cables & Connectors of FSP Hydro G Pro 1000W

Description	Cable Count	Connector Count (Total)	Gauge	In Cable Capacitors
ATX connector 20+4 pin (600mm)	1	1	18-22AWG	No
4+4 pin EPS12V (700mm)	2	2	18AWG	No
6+2 pin PCIe (650mm+150mm)	2	4	18AWG	No
6+2 pin PCIe (500mm+150mm)	1	2	18AWG	No
12+4 pin PCIe 600W (700mm)	1	1	16-24AWG	No
SATA (500mm+150mm+150mm+150mm)	2	8	18AWG	No
SATA (500mm+150mm) / 4-pin Molex (+150mm+100mm)	2	4 / 4	18AWG	No
SATA (500mm+150mm) / 4-pin Molex (+150mm) / FDD (+150mm)	1	2 / 1 / 1	18-22AWG	No
AC Power Cord (1350mm) - C13 coupler	1	1	18AWG	-

The cables are long, and the amount of connectors is satisfactory. The single 12VHPWR connector can deliver up to 600W. According to Intel's test plan, a 1000W ATX v3.0 PSU should be equipped with a 450W 12VHPWR connector, but most brands don't pay attention to this and use 600W connectors to make sure that the NVIDIA RTX 4090 graphics cards can go all the way up to 600W. Not all 4090s have such high maximum power limits, though.

Component Analysis of FSP Hydro G Pro 1000W

We strongly encourage you to have a look at our PSUs 101 article, which provides valuable information about PSUs and their operation, allowing you to better understand the components we're about to discuss.

General Data
Manufacturer (OEM)	FSP
PCB Type	Double Sided
Primary Side
Transient Filter	4x Y caps, 2x X caps, 2x CM chokes, 1x MOV
Inrush Protection	NTC Thermistor SCK-056 (5 Ohm) & Relay
Bridge Rectifier(s)	2x HY GBJ2506 (600V, 25A @ 100°C)
APFC MOSFETs	2x Infineon IPA60R120P7 (600V, 16A @ 100°C, Rds(on): 0.12Ohm)
APFC Boost Diode	1x CREE C3D08060A (600V, 8A @ 150°C)
Bulk Cap(s)	1x Nippon Chemi-Con (450V, 680uF, 3,000h @ 105°C, KHS)
Main Switchers	2x Magnachip MMFT60R115PC (600V, 20.9A @ 100°C, Rds(on): 0.115Ohm)
APFC Controller	Infineon ICE2PCS02G
Resonant Controller	Champion CM6901T2X
Topology	Primary side: APFC, Half-Bridge & LLC converter Secondary side: Synchronous Rectification & DC-DC converters
Secondary Side
+12V MOSFETs	6x Infineon BSC014N04LSI (40V, 123A @ 100°C, Rds(on): 1.45mOhm)
5V & 3.3V	DC-DC Converters: 6x NEC 2SK3062-ZJ (60V, 70A, Rds(on): 8.5mOhm) PWM Controller(s): ANPEC APW7159C
Filtering Capacitors	Electrolytic: 4x Nippon Chemi-Con (2-5,000h @ 105°C, KZE), 2x Rubycon (3-6,000h @ 105°C, YXG), 2x Rubycon (2-10,000h @ 105°C, YXF), 1x Rubycon (6-10,000h @ 105°C, ZLH), 1x TK (105°C) Polymer: 29x Nippon Chemi-Con, 1x NIC
Supervisor IC	Weltrend WT7527RA (OCP, OVP, UVP, SCP,PG)
Fan Controller	APW9010
Fan Model	Protechnic Electric MGA12012XF-O25 (120mm, 12V, 0.52A, Fluid Dynamic Bearing)
5VSB Circuit
Rectifier	1x CET CEF04N7G (700V, 4A, Rds(on): 3.3Ohm) & 1x PFC P15L50SP SBR (50V, 15A)
Standby PWM Controller	97CL2N13

The small PCB is equipped with equally small heat sinks. Except for the transient filter, the other circuits have enough space between electronic parts to allow for decent airflow. It is good to see the filtering caps on the secondary side being on the clear, without anything blocking airflow to them. Typically, for an FSP platform, we find some potentiometers on a vertical PCB, which might look tempting to adjust, but you should not do it! The build quality is high, and all parts that FSP used are of high quality, too. FSP is among the few OEMs using bulk caps rated for 3,000h @ 105°C. All other brands use 2,000h @ 105°C bulk caps